Call (260) 226-8800★ 4.9, 257 Google reviews

Siding | Faze Construction Blog

Can You Install Vinyl Siding on a House With Metal Studs?

Can vinyl siding be installed over a metal-framed home? See how Faze Construction solved an unusual Fort Wayne siding project using specialized fasteners, flashing and installation techniques.

Call (260) 226-8800
  • Free inspection
  • See your cost before you call

Most residential siding projects are relatively predictable.

You remove the existing siding, inspect the wall assembly, address any damaged sheathing or wood rot, install the proper moisture-management system, and fasten the new siding according to the manufacturer's requirements.

Home with new black siding
A finished Faze siding job.

But every once in a while, you open up a house and find something you weren't expecting.

That's exactly what happened on a recent Faze Construction siding project in the Fort Wayne area.

We started this approximately 23-square (2,300-square-foot) siding project expecting conventional wood framing.

Instead, after removing the existing exterior, we discovered something considerably less common in residential construction:

The home was framed with metal studs.

And that created an interesting problem.

How do you properly install vinyl siding designed to last for decades when there's no conventional wood stud to nail into?

The answer wasn't to tell the homeowner their project couldn't be done.

It was to change the fastening system.

Why Metal Studs Create a Problem for Vinyl Siding

Most traditionally framed homes use dimensional lumber, commonly wood 2x4 or 2x6 studs, behind the exterior wall assembly.

That provides a suitable substrate for an approved siding fastening system when the entire wall assembly is constructed correctly.

On this particular home, however, we discovered metal framing.

That matters because you can't simply treat a metal stud like a wood stud.

Driving an ordinary siding nail toward thin metal framing doesn't provide the same reliable fastening you'd expect from an appropriate fastener penetrating wood.

And that's not something we're willing to ignore.

If we're installing a siding system that's supposed to provide long-term performance and carry strong warranty protection, the fastening system underneath it needs to be appropriate for the actual wall construction.

So we had to adapt.

The Solution: A Screw-Fastened Vinyl Siding System

For this particular wall assembly, our solution was to use approximately two-inch specialized screws capable of fastening the siding system into the metal framing.

Instead of hammering siding nails into conventional wood framing, each siding course had to be individually fastened with screws at the appropriate framing locations.

The metal studs on this particular home were approximately 24 inches on center.

That meant we could fasten at every stud location, keeping the spacing at approximately two feet or less across each piece.

Depending on the length and location of a siding panel, that could mean roughly seven individual screws in a single piece of siding.

Multiply that across an approximately 23-square siding project and something seemingly minor becomes a major installation consideration.

By the time the project was completed, we were dealing with roughly 1,600 individual screw fasteners instead of a conventional nail installation.

That's a lot of screws.

But that's also the difference between simply making siding look installed and taking the time to develop a fastening strategy appropriate for the home.

Vinyl Siding Needs to Move

There's another important part of this conversation.

Vinyl siding isn't supposed to be clamped rigidly against the house.

Vinyl expands and contracts as temperatures change. That's particularly important here in Northeast Indiana, where an exterior can experience summer heat followed by freezing winter temperatures.

Whether you're using approved nails, screws, or another manufacturer-permitted fastening method, the installation needs to account for that movement.

Fasteners generally need to be properly positioned within the siding's fastening slots and installed according to the siding manufacturer's requirements rather than simply driven as tightly as possible.

Otherwise, improperly fastened vinyl can potentially:

So switching from nails to screws doesn't mean abandoning proper vinyl installation practices.

The fastener changes. The attention to installation detail doesn't.

Then We Found Another Problem: The Windows

The siding wasn't the only unusual part of this house.

The existing windows had nail flanges incorporated into metal extrusions around the stud cavities.

Ordinarily, removing a nail-flange window from conventional construction is relatively straightforward.

Not here.

The existing metal components had to be carefully cut and ground out by hand so the old windows could be removed without unnecessarily damaging the surrounding assembly.

Once the openings were properly prepared, we could address the flashing and moisture-management details and install the new vinyl new-construction windows.

And once again, because we were dealing with metal framing, the fastening method had to account for that construction.

We couldn't simply pretend there was wood behind the wall and proceed normally.

Metal Studs Don't Eliminate the Need for Proper Flashing

This is where homeowners can sometimes get distracted by the unusual part of the project.

Yes, the metal framing changed our fastening method.

But it didn't change the fundamentals of exterior construction.

The home still needs an appropriately designed water-management system.

That means paying attention to things like:

Your siding is not your home's only defense against water.

A properly built exterior is a system of overlapping components designed to direct water down and away from the structure.

Metal framing doesn't change that principle.

What About Wood Rot?

Ironically, suspected wood rot was one of the reasons this project became interesting in the first place.

The homeowner believed there could be deterioration behind portions of the existing siding, and we did discover areas requiring attention.

But once we opened the wall system, we also discovered the metal framing.

This illustrates something we tell homeowners constantly:

Nobody can see through a wall.

An experienced contractor can identify warning signs and make educated assessments, but some conditions simply aren't visible until the existing exterior is removed.

You might uncover:

That's why the contractor's response to an unexpected condition is often more important than whether the condition was predicted beforehand.

Did We Charge the Homeowner More?

In this particular case, we didn't.

The metal framing was such an unusual discovery that we worked through the additional labor and fastening requirements without adding the additional cost to the homeowner.

That shouldn't be interpreted to mean every metal-framed siding project will cost the same as a conventional installation.

Normally, unusual substrates can create additional costs because of:

Every home needs to be evaluated individually.

This one just happened to be unusual enough that we figured we'd take care of our customer, and get a pretty good story out of it.

Sometimes you find wood rot. Sometimes you find an entire house made out of metal.

Can You Put Vinyl Siding on a Metal-Framed House?

Yes, in many situations, you can.

Discovering metal studs does not automatically mean a homeowner can't install vinyl siding.

It means the contractor needs to stop, understand the wall assembly, determine an appropriate fastening method, and verify that the proposed installation meets applicable manufacturer instructions and building requirements.

The solution may involve approved screws or another fastening system designed for the particular substrate.

What you shouldn't do is blindly continue installing the house exactly as though it were conventional wood framing.

What Should You Do If Your Contractor Finds Metal Studs?

Don't panic.

Ask some important questions:

What are we fastening the siding into?

The contractor should understand exactly what will support the new siding.

What fastener are you using?

The fastener should be appropriate for the substrate and siding system.

What's the fastening spacing?

The answer should be based on the actual siding system, substrate, wind requirements, and manufacturer instructions, not guesswork.

Will the siding still be able to expand and contract?

Vinyl needs appropriate freedom of movement.

How are the windows being handled?

Window removal and replacement may become more complicated when metal framing or unusual extrusions are involved.

How is the weather barrier being integrated?

A different framing material doesn't eliminate the need for proper water management.

And finally:

Does this installation maintain the applicable product warranty?

That's a particularly important question anytime a contractor deviates from the installation method typically used on a conventional wood-framed home.

Why Installation Matters More Than Most Homeowners Realize

Homeowners understandably spend a lot of time choosing siding.

What color?

What profile?

Insulated or standard vinyl?

What accents?

What warranty?

Those decisions matter.

But the siding you can see is only half the project.

The screws, fasteners, flashing, weather barrier, sheathing, window details, and installation practices behind the siding determine whether that beautiful exterior continues performing years from now.

Our metal-framed project was a perfect example.

From the street, the homeowner will simply see a finished vinyl siding and window project.

Behind that finished exterior are approximately 1,600 specialized fasteners and a completely different installation approach necessitated by a condition nobody could fully see until demolition began.

That's the stuff homeowners don't normally see on the estimate.

But it's exactly the stuff that matters.

Siding Installation in Fort Wayne, Indiana

At Faze Construction, we install siding and exterior systems throughout Fort Wayne and Northeast Indiana.

Whether your home has conventional wood framing, unusual existing siding, suspected wood rot, window problems, moisture concerns, or apparently decides to surprise everyone with metal studs, we'll evaluate what's actually there and determine the appropriate path forward.

An unusual condition doesn't necessarily mean your project can't be completed.

Sometimes it just means your contractor needs to know how to solve a problem.

If you're considering new siding, schedule an exterior inspection with Faze Construction. We'll evaluate the existing system, explain what we find, and help you build an exterior designed for long-term performance.

Common questions

What About Wood Rot?

Ironically, suspected wood rot was one of the reasons this project became interesting in the first place.

Did We Charge the Homeowner More?

The metal framing was such an unusual discovery that we worked through the additional labor and fastening requirements without adding the additional cost to the homeowner.

Can You Put Vinyl Siding on a Metal-Framed House?

Discovering metal studs does not automatically mean a homeowner can't install vinyl siding.

What homeowners say about Faze

4.9 stars from 257 Google reviews. Here is what Fort Wayne homeowners said in their own words.

★★★★★
“Faze inspected my roof and found storm/hail damage and was able to work with my insurance company to get new roof installation. Faze worked for my benefit and provided excellent service. Faze went the extra mile every step of the process and ensured that I was informed and answered any questions that I had along the way. I would recommend them to my closest friends and family!”

Richard Short

Roof replacement · Google review

★★★★★
“Faze Roofing and Construction came out and gave us an inspection and quote the same day. They were out the next week right before Thanksgiving and had the roof completed within a day. Super happy with the professionalism and work that was done. Their pricing was super competitive! We look forward to using them for our Christmas lights this winter and in the future!”

Maegen Barbour

Roof replacement · Homeowner review

Read all nine reviews →

Book Your Free Inspection

Tell us about your home and your project. The form takes about two minutes, and a Faze team member follows up to confirm your inspection time.

Seabron Weaver in front of the Faze trailer

Photos, an honest report and an exact written quote. No pressure.

Your inspector takes photos of what they find, walks you through them, and leaves you with a written quote. You decide what happens next.

★ 4.9, 257 Google reviews

Step 1 of 4

Your cost range

If you used the calculator, your range shows here. If not, your exact written quote comes from the free inspection.

Your range will show here after you use the calculator above.

A few quick questions

Who will be present at the inspection?

Both homeowners / decision makers
Just me
My spouse or partner will join later
Other

Credit score range

Above 650
600 to 650
Below 600
Not sure / Prefer not to say

How soon do you want the job done?

As soon as possible / storm damage
Within 2 weeks
Within 1 to 3 months
Just researching / 3 months or more

Are you the homeowner?

Yes, I own this home
No, I rent
No, I manage the property

Review and send

Thank you. Your request is in.

A Faze team member will follow up to confirm your free inspection time. If you need us sooner, call (260) 226-8800.

Download a copy of your request

Ready to get your free inspection?

See your price range in about a minute, then book a free inspection and get your exact written quote.